Commit 47cfbf32fd ("*: add most of the
required setup_common_bufsiz() calls") switched this tool over to use
the common_bufsiz logic but missed including the header leading to a
build failure when enabled:
selinux/setfiles.c:80:30: error: 'bb_common_bufsiz1' undeclared (first use in this function)
URL: https://bugs.gentoo.org/600106
Reported-by: Jonas Jelten <jj@stusta.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
(cherry picked from commit 1cda879080)
The somewhat new "unpack in memory" code was broken
for xmalloc_open_zipped_read_close() on NOMMU: we seek back
over signature, but then expect it to be already consumed.
Stop seeking back in this case.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
"modprobe minix; echo $?"
Was:
modprobe: corrupted data
modprobe: read error from 'kernel/fs/minix/minix.ko.xz': No such file or directory
modprobe: corrupted data
modprobe: read error from 'kernel/fs/minix/minix.ko.xz': No such file or directory
modprobe: corrupted data
modprobe: read error from 'kernel/fs/minix/minix.ko.xz'
modprobe: 'kernel/fs/minix/minix.ko.xz': Success
0
Now:
modprobe: corrupted data
modprobe: read error from 'kernel/fs/minix/minix.ko.xz'
1
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Both calls to run_applet_and_exit are followed by the same code
to print an error message and return status 127. Remove this
duplication and make run_applet_and_exit static.
function old new delta
run_applet_and_exit 675 667 -8
main 119 92 -27
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-35) Total: -35 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
A recent commit made it possible to disable BusyBox's --install
and --list options. However it also stopped "busybox <applet>
<params>" from working.
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Some users start ntpd on boot, and don't babysit it. If it dies because
DNS is not yet up and therefore NTP servers can't be found, users are
not happy.
Example behavior with a peer name which can't be resolved:
ntpd: bad address 'qwe.rty.ghj.kl'
...5 sec...
ntpd: bad address 'qwe.rty.ghj.kl'
ntpd: bad address 'qwe.rty.ghj.kl'
ntpd: bad address 'qwe.rty.ghj.kl'
ntpd: bad address 'qwe.rty.ghj.kl'
ntpd: bad address 'qwe.rty.ghj.kl'
ntpd: bad address 'qwe.rty.ghj.kl'
ntpd: bad address 'qwe.rty.ghj.kl'
ntpd: bad address 'qwe.rty.ghj.kl'
ntpd: bad address 'qwe.rty.ghj.kl'
...
Based on the patch by Kaarle Ritvanen <kaarle.ritvanen@datakunkku.fi>
function old new delta
resolve_peer_hostname - 81 +81
ntpd_main 1130 1061 -69
------------------------------------------------------------------------------
(add/remove: 1/0 grow/shrink: 0/1 up/down: 81/-69) Total: 12 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
If it's disabled, code shrinks by about 900 bytes:
function old new delta
usr_bin 10 - -10
usr_sbin 11 - -11
install_dir 20 - -20
applet_install_loc 184 - -184
run_applet_and_exit 686 21 -665
------------------------------------------------------------------------------
(add/remove: 0/4 grow/shrink: 0/1 up/down: 0/-890) Total: -890 bytes
text data bss dec hex filename
911327 493 7336 919156 e0674 busybox_old
909848 493 7336 917677 e00ad busybox_unstripped
but busybox executable by itself does not say anything useful:
$ busybox
busybox: applet not found
Based on the patch by Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This is the only non-debug use of ether_ntoa(). By not using it,
we reduce bss:
function old new delta
arping_main 1568 1665 +97
static.asc 18 - -18
ether_ntoa 57 - -57
------------------------------------------------------------------------------
(add/remove: 0/2 grow/shrink: 1/0 up/down: 97/-75) Total: 22 bytes
text data bss dec hex filename
911020 493 7352 918865 e0551 busybox_old
911069 493 7336 918898 e0572 busybox_unstripped
Also, "standard" arping zero-pads MAC. ether_ntoa() does not.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Use designated initializers for struct msghdr.
The struct layout is non-portable and musl libc does not match what busybox expects.
Signed-off-by: Szabolcs Nagy <nsz@port70.net>
Tested-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The result of looking at "grep -F -B2 '*fill*' busybox_unstripped.map"
text data bss dec hex filename
829901 4086 1904 835891 cc133 busybox_before
829665 4086 1904 835655 cc047 busybox
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Bash doesn't expand its $'...' construct in double quotes:
$ echo "$'a\tb'"
$'a\tb'
Change BusyBox ash to do the same. This also fixes a problem with
here documents where BusyBox ash gave an incorrect result for:
$ cat <<EOF
> '$'
> EOF
'$'
Reported-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This makes "make menuconfig" also work on systems where ncurses is not
installed in a standard location (such as on NixOS).
This patch changes ccflags() so that it tries pkg-config first, and only
if pkg-config fails does it go back to the fallback/manual checks. This
is the same algorithm that ldflags() already uses.
Signed-off-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Makefiles call the respective interpreter explicitly, but this makes
it easier to use the scripts manually.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current code does this:
if [ -f /usr/include/ncursesw/curses.h ]; then
echo '-I/usr/include/ncursesw -DCURSES_LOC="<ncursesw/curses.h>"'
elif [ -f /usr/include/ncurses/ncurses.h ]; then
echo '-I/usr/include/ncurses -DCURSES_LOC="<ncurses.h>"'
elif [ -f /usr/include/ncurses/curses.h ]; then
echo '-I/usr/include/ncurses -DCURSES_LOC="<ncurses/curses.h>"'
[...]
This is merely inconsistent:
- adding the full path to the directory in the -I directive,
- especially since that path is already a sub-path of the system
include path,
- and then repeating the sub-path in the #include directive.
Rationalise each include directive:
- only use the filename in the #include directive,
- keep the -I directives: they are always searched for before the
system include path; this ensures the correct header is used.
Using the -I directives and the filename-only in #include is more in
line with how pkg-config behaves, eg.:
$ pkg-config --cflags ncursesw
-I/usr/include/ncursesw
This paves the way for using pkg-config for CFLAGS, too, now we use it
to find the libraries.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When building ncurses with --with-termlib several symbols get moved from
libncurses.so to libtinfo.so. Thus when linking with libncurses.so, one
additionally needs to link with libtinfo.so.
The ncurses pkg-config module will be used to detect the necessary libs for
linking. If not available the old heuristic for detection of the ncurses libs
will be used.
Signed-off-by: Justin Lecher <jlec@gentoo.org>
Tested-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The ncurses library allows for extended colors. The support for extended
colors support depends on wide-character support. ncurses headers
enable extended colors (NCURSES_EXT_COLORS) only when wide-character
support is enabled (NCURSES_WIDECHAR).
The "make menuconfig" uses wide-character ncursesw library, which can be
compiled with wide-character support, but does not define NCURSES_WIDECHAR
and it's using headers without wide-character (and extended colors) support.
This fixes problems with colors on systems with enabled extended colors
(like PLD Linux). Without this patch "make menuconfig" is hard to use.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The correct syntax for gcc -x is "gcc -x assembler", not
"gcc -xassembler". Even though the latter happens to work, the former
is what is documented in the manual page and thus what gcc wrappers
such as icecream do expect.
This isn't a cosmetic change. The missing space prevents icecream from
recognizing compilation tasks it can't handle, leading to silent kernel
miscompilations.
Besides me, credits go to Michael Matz and Dirk Mueller for
investigating the miscompilation issue and tracking it down to this
incorrect -x parameter syntax.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Cc: Bernhard Walle <bernhard@bwalle.de>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Import libraries on Cygwin and MinGW/MSYS use the .dll.a suffix, so
checking this suffix is necessary to make sure ncurses will still be
found when built without static libraries.
Signed-off-by: Yaakov Selkowitz <yselkowitz@users.sourceforge.net>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 8c41e5e363db55d91aa3b1cdce4ab02ad9821de7 added a check for
ncursesw/curses.h for the case where ncurses and ncursesw are build
separately but only one is installed. But if both are installed,
the headers ncurses/curses.h and ncursesw/curses.h differ, and since
libncursesw will be found first, so should ncursesw/curses.h.
Signed-off-by: Yaakov Selkowitz <yselkowitz@users.sourceforge.net>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In 60f33b8 (kconfig: get rid of stray a.o, support ncursesw, 2006-01-15),
support to link menuconfig with ncursesw library was added. To compute
the linker command option -l, we check "libncursesw.{so,a,dylib}" to allow
ncursesw to be used as a replacement ncurses. However, when checking what
header file to include, we do not check /usr/include/ncursesw directory.
Add /usr/include/ncursesw to the list of directories that are checked.
With this patch, on my Debian Lenny box with libncursesw5-dev package but
not libncurses5-dev package, I can say "make menuconfig".
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This reverts commit e91bc53d0c.
Let's get back to a state that matches upstream so we can pull in all of
their fixes from the last few years.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The loop
for (j = ARRAY_SIZE(applet_nameofs)-1; j >= 0; j--) {
was intended to terminate when j goes negative, so j needs to be signed.
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Presumably, bb_info_msg was used here for syslog logging (-l),
but there is no actual code to activate syslog logging.
Added a TODO note on that, so that selinux users would notice
and fix if needed.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Historic "System Maintenance Mode" message is a tiny bit cryptic.
Let's say explicitly what we are doing: we are giving user a shell
(presumably to do some maintenance in single-user mode).
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The array applet_nameofs consumes two bytes per applet. It encodes
nofork/noexec flags
suid flags
the offset of the applet name in the applet_name string
Change the applet_table build tool to store the flags in two separate
arrays (applet_flags and applet_suid). Replace applet_nameofs[] with a
smaller version that only stores a limited number of offsets.
This requires changes to the macros APPLET_IS_NOFORK, APPLET_IS_NOEXEC
and APPLET_SUID.
According to Valgrind the original find_applet_by_name required
353 cycles per call, averaged over all names. Adjusting the number
of known offsets allows space to be traded off against execution time:
KNOWN_OFFSETS cycles bytes (wrt KNOWN_OFFSETS = 0)
0 9057 -
2 4604 32
4 2407 75
8 1342 98
16 908 130
32 884 194
This patch uses KNOWN_OFFSETS = 8.
v2:
Remove some dead code from the applet_table tool;
Treat the applet in the middle of the table as a special case.
v3:
Use the middle applet to adjust the start of the linear search as
well as the last applet found.
v4:
Use an augmented linear search in find_applet_by_name.
Drop the special treatment of the middle name from get_applet_name:
most of the advantage now derives from the last stored value.
v5:
Don't store index in applet_nameofs, it can be calculated.
v6:
Tweaks by Denys
function old new delta
find_applet_by_name 25 125 +100
applet_suid - 92 +92
run_applet_no_and_exit 452 460 +8
run_applet_and_exit 695 697 +2
applet_name_compare 31 - -31
applet_nameofs 734 14 -720
------------------------------------------------------------------------------
(add/remove: 1/1 grow/shrink: 3/1 up/down: 202/-751) Total: -549 bytes
text data bss dec hex filename
925464 906 17160 943530 e65aa busybox_old
924915 906 17160 942981 e6385 busybox_unstripped
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
As reported in bug 8506:
$ X=abcdÉfghÍjklmnÓpqrstÚvwcyz
$ echo ${#X}
abcd26
The result should be 26.
This regression was introduced by:
<d68d1fb> 2015-05-18 [Ron Yorston] ash: code shrink around varvalue
The length in characters was being used to discard the contents of
the variable instead of the length in bytes.
URL: https://bugs.busybox.net/8506
Reported-by: Martijn Dekker <martijn@inlv.org>
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In coreutils/ls.c, 1.19 introduced commit
2f7d9e8903, removing the variable tabstops and
hard coding the column separation to 2 characters, but was not done correctly.
The column_width assumes a gap of 1 character, so the computed number of
columns exceeds the terminal width when many small files are encountered.
A minor problem but surprisingly annoying.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Otherwise, "-t 0" usage may end up sending them forever
if server does not respond.
function old new delta
udhcpc_main 2846 2836 -10
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
RFC2131 paragraph 4.1 states DHCP messages broadcast by a client prior to
that client obtaining its IP address must have the source IP address
field in the header set to 0.
Request messages transmitted in renewing and rebinding state need to use
the obtained IP address as source IP address in the header; this behavior
lines up with other implementations like ISC dhcp client.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Let udhcpd retain the information about expired leases when restarting
so that the leases are reserved until they possibly become the oldest
expired lease.
This reduces the frequency of IP address changes for example when the
DHCP server and a group of clients, who do not store and request their
previously offered IP address across restarts, are collectively restarted
and the startup order of the clients are not guaranteed.
Signed-off-by: Christian Lindeberg <christian.lindeberg@axis.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This patch allow to have multiple interface definitions, much like
Debian's ifupdown. More specifically, it removes the check for a
duplicate definition, so the impact on binary size should be fairly
minimal.
This configuration:
iface eth0 inet static
address 192.168.0.15
netmask 255.255.0.0
gateway 192.168.0.1
iface eth0 inet static
address 10.0.0.1
netmask 255.255.255.0
Will add two addresses to eth0 if ip is used. If ifconfig is used,
the standards methods will likely not stack, but the administrator may
still use the manual method. The DHCP method may work depending on the
DHCP client in use.
This is a fairly advanced feature for power users who knows what they
are doing. There are not many other network configuration systems that
allows multiple addresses on an interface.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The non-fancy version of the from_cpuset uses CPU_SETSIZE as if it
represents the number of bytes in the cpuset, while it is actually
the number of bits. This leads to out-of-bounds accesses on the
cpu_set_t in the big-endian case. Basically all uses of CPU_SETSIZE
have to be divided by 8. This is done correctly in the fancy version
of from_cpuset.
In addition, the big-endian case is completely wrong to begin with.
All standard C libraries that I know of implement cpu_set_t as an
unsigned long array, so both for big and little endian, the least
significant bits are in the beginning of the array. Therefore, the
approach taken for the little endian case is equally valid. We only
need special handling for big endian when CPU_SETSIZE is large and
we use an unsigned long long to get more bits out.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Building & running with ASAN is super helpful, so add a dedicated config
knob for it. This way people don't have to guess at the right compiler
settings in order to get a good build. We can just tell people to enable
this one option.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When launched as PID 1 and after parsing its arguments, init wipes all
all of them except argv[0] and rewrites argv[0] to contain only "init",
so that its command-line appears solely as "init" in tools such as ps.
This patch adds the FEATURE_INIT_MODIFY_CMDLINE which, if set to n, will
make init preserve all its arguments including argv[0], be they parsed or
ignored.
The original command-line used to launch init can then be retrieved in
/proc/1/cmdline on Linux, for example.
Signed-off-by: Nicolas Carrier <nicolas.carrier@parrot.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
After commit 8e74adab01
("libbb: make INET[6]_rresolve use sockaddr2{host,dotted}_noport")
INET_sprint6 uses more than just sin6_addr, it also tries to display the
scope id, which is uninitialized when called from ife_print6.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This patch fixes compiling busybox with FEATURE_UTMP and _WTMP enabled.
musl, while not really support utmp/wtmp, provides stub functions, as well
as variables such as _PATH_UTMP, so that programs using utmp or wtmp can
still compile fine.
My reasoning for this patch is that on Exherbo, I'm currently trying to get
us to be able to use the same busybox config file for both glibc and musl
systems, using utmp/wtmp on systems that support it, and using the stubs
on musl without needing two different configs.
As of latest musl git, it provides all utmp functions needed; 1.1.12 doesn't,
but I sent a patch to Rich to add the utmp{,x}name functions expected to
exist, which was merged into musl upstream.
Signed-off-by: Kylie McClain <somasissounds@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
printf wasn't correctly handling \c in an argument to the %b format
specifier.
printf %bXX OK\\c
returned 'OK\cXX' rather than the expected 'OK'.
function old new delta
printf_main 886 899 +13
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Reported by gcc (Debian 5.3.1-4) 5.3.1 20151219
shell/ash.c: In function 'evaltree':
shell/ash.c:8432:19: warning: logical not is only applied to the left hand side of comparison
Signed-off-by: Cristian Ionescu-Idbohrn <cristian.ionescu-idbohrn@axis.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
CC util-linux/swaponoff.o
cc1: warnings being treated as errors
util-linux/swaponoff.c: In function 'swap_enable_disable':
util-linux/swaponoff.c💯 warning: passing argument 1 of 'resolve_mount_spec' from incompatible pointer type
make[1]: *** [util-linux/swaponoff.o] Error 1
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The -e option should only apply to swapon, and it should swallow all
errors/warnings when the device does not exist. So delete the flag
from the swapoff patch and unify the check in the swapoff path.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The user might be including options in their LDFLAGS (like -fuse-ld=gold)
that change the behavior of the linker and thus change the results of the
flag tests. Make sure we include the user's LDFLAGS when running these
tests so we filter out flags that will fail when used later on.
URL: https://bugs.gentoo.org/499712
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Where the POSIX shell allows functions to be defined as:
name () compound-command [ redirections ]
bash adds the alternative syntax:
function name [()] compound-command [ redirections ]
Implement this in ash's bash compatibility mode. Most compound
commands work (for/while/until/if/case/[[]]/{}); one exception is:
function f (echo "no way!")
The other two variants work:
f() (echo "ok")
function f() (echo "also ok")
function old new delta
parse_command 1555 1744 +189
tokname_array 232 240 +8
.rodata 155612 155566 -46
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 2/1 up/down: 197/-46) Total: 151 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This makes busybox i2cdump compatible with the upstream version, which
also displays the numeric error value in case of a block read failure.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
We should bail-out if i2c_smbus_read_block_data() or
i2c_smbus_read_i2c_block_data() return 0 or less. Add the missing check
for the former and fix the existing for the latter.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Currently we're calling i2c_smbus_read_block_data() for both 'i' and 's'
mode parameters. If the bus doesn't support SMBus block mode, then the
i2c access ioctl() fails. Make i2cdump behave compatibly with upstream
version by calling i2c_smbus_read_i2c_block_data() for I2C block.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
We currently read data twice in byte mode. Add a check to avoid calling
i2c_smbus_read_i2c_block_data() if we're not in I2C or SMBus block mode.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
If the bus doesn't support SMBus Quick Write or Receive Byte commands
and we're running in auto mode all addresses will be skipped resulting
in an empty table being printed.
This is caused by not restoring the auto mode after it's been changed
for certain address ranges - we need an additional variable to hold the
temporary state.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
If /tmp/test.sh is a script that tries to run a second script which
happens to be non-executable this:
command . /tmp/test.sh
causes a seg fault.
This is because clearredir is called in the error path to clear the
stack of redirections. The normal path then calls popredir, but popredir
fails when the stack is empty.
Reported-by: Bastian Bittorf <bittorf@bluebottle.com>
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
evalcommand always clobbers the exit status in case of an EXEXEC
which means that exec always fails with exit status 2 regardless
of what it actually returns.
This patch adds the missing check for EXEXEC so that the correct
exit status is preserved. It causes the test ash-misc/exec.tests
to succeed.
Based on commit 7f68426 in dash git, by Herbert Xu.
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The exec builtin should return an exit status of 127 if the command
can't be found. It doesn't: it returns 2.
If the command builtin is used to source a script that runs a second
script that doesn't exist ash should issue an error. Instead it seg
faults.
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
In standalone shell mode search the applet table as well as PATH
when tab completing a command.
Use a stupid linear search: we're also about to read all the
directories on PATH so efficiency isn't a big concern.
function old new delta
add_match - 53 +53
complete_cmd_dir_file 687 724 +37
------------------------------------------------------------------------------
(add/remove: 1/0 grow/shrink: 1/0 up/down: 90/0) Total: 90 bytes
Signed-off-by: Ron Yorston <rmy@frippery.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Processing of here documents in ash has had a couple of breakages
which are now the subject of tests. This commit should fix both.
It is based on the following commit in dash git by Herbert Xu:
<7c245aa> [PARSER] Simplify EOF/newline handling in list parser
(See git://git.kernel.org/pub/scm/utils/dash/dash.git)
Reported-by: Natanael Copa <ncopa@alpinelinux.org>
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Save the value of the checkkwd flag to prevent it being clobbered
during recursion.
Based on commit ec2c84d from git://git.kernel.org/pub/scm/utils/dash/dash.git
by Herbert Xu.
function old new delta
readtoken 190 203 +13
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 1/0 up/down: 13/0) Total: 13 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The command builtin should only check the default path, not $PATH,
when the -p flag is used along with -v/-V.
Based on commits 65ae84b (by Harald van Dijk) and 29ee27d (by Herbert
Xu) from git://git.kernel.org/pub/scm/utils/dash/dash.git).
function old new delta
commandcmd 72 87 +15
describe_command 437 450 +13
typecmd 84 86 +2
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 3/0 up/down: 30/0) Total: 30 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
busybox sh -c 'command --' segfaults because parse_command_args
returns a pointer to a null pointer.
Based on commit 18071c7 from git://git.kernel.org/pub/scm/utils/dash/dash.git
by Gerrit Pape.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Based on commit 49b82fc from git://git.kernel.org/pub/scm/utils/dash/dash.git
by Herbert Xu.
function old new delta
parse_command 1563 1555 -8
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8) Total: -8 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Newline is a valid delimiter between the variable name and `in`
keyword in for loops.
Based on commit 22e8fb4 from git://git.kernel.org/pub/scm/utils/dash/dash.git
by Herbert Xu.
function old new delta
parse_command 1568 1563 -5
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-5) Total: -5 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This used to work but doesn't now:
foo () {
cat <<EOF && { echo "$1" ; }
$1
EOF
}
foo "bar"
Reported-by: Natanael Copa <ncopa@alpinelinux.org>
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The virtual y can be larger - and we can be even writing there since
we are taking into account the y offset. Avoids possible crash.
But use it only if set, seems it is not set if virtual area is not
allocated (though, often fbcon allocates some scrollback area).
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Add support for --no-name long option. Just silently ignore it
like the short -n option.
This allows to use busybox gzip with Lynx browser.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
now, we can do printf "a\tb\tcdef\n" | ./busybox tr -d "\1-\14b-e"
af
and bonus, we save some bytes.
function old new delta
expand 718 699 -19
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-19) Total: -19
bytes
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
IPv6 routes need the device argument for link-local routes, or they
cannot be used at all. E.g. "gateway fe80::def" seems to be used in
some places, but kernel refuses to insert the route unless device
name is explicitly specified in the route addition.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
MONOTONIC_SYSCALL=y by default
FEATURE_LAST_SMALL is gone: now FEATURE_LAST_FANCY is a "bool", not a "choice".
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Saves 87 bytes. Assuming, of course, all platforms have it.
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Make -I imply -r (GNU findutils seems to do the same).
Fixes the following bug:
$ echo -n | xargs -I% echo %
Segmentation fault
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
systemd people are not willing to play nice with the rest of the world.
Therefore there is no reason for the rest of the world to cooperate with them.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
We don't use it in final link, should not use it in check_FOO then.
This uncovered a logic bug in glibc check...
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
To that end, *make it complain* when check_cc fails on options
we usually want to succeed.
text data bss dec hex filename
929697 932 17692 948321 e7861 busybox-1.23.2/busybox
915361 911 17484 933756 e3f7c busybox-1.23.2.fixed/busybox
927725 932 17448 946105 e6fb9 busybox-1.24.0/busybox
913630 911 17240 931781 e37c5 busybox-1.24.0.fixed/busybox
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This commit adds support for the -R flag of setarch, which disables
randomization of the virtual address space.
function old new delta
setarch_main 115 150 +35
packed_usage 30664 30651 -13
Signed-off-by: Jan Heylen <heyleke@gmail.com>
Signed-off-by: Thomas De Schampheleire <thomas.de.schampheleire@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
invarg(a,b) - "invalid argument", but how a and b enter the message?
invarg_1_to_2(a,b) is somewhat easier to read: "invalid argument 'a' to 'b'"
Audit of usage revealed a number of bad uses, with too long messages.
text data bss dec hex filename
938848 932 17448 957228 e9b2c busybox_old
938788 932 17448 957168 e9af0 busybox_unstripped
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This patch ports the 'ip neigh' command, originally written by Alexey
Kuznetsov, <kuznet@ms2.inr.ac.ru>, to busybox.
The base of the port is the version of iproute that shipped with
Debian Squeeze, taken from:
http://http.debian.net/debian/pool/main/i/iproute/iproute_20100519.orig.tar.gz
This patch has actively been used by the Open Network Install
Environment (ONIE) project for over 3 years without incident.
function old new delta
print_neigh - 933 +933
ipneigh_list_or_flush - 742 +742
get_hz - 109 +109
do_ipneigh - 62 +62
do_iproute 2112 2153 +41
packed_usage 30647 30667 +20
ipneigh_main - 14 +14
static.ip_neigh_commands - 12 +12
static.nuds - 9 +9
static.ip_func_ptrs 32 36 +4
print_route 1858 1727 -131
------------------------------------------------------------------------------
(add/remove: 8/0 grow/shrink: 3/1 up/down: 1946/-131) Total: 1815 bytes
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
If FEATURE_WGET_OPENSSL and FEATURE_WGET_SSL_HELPER are both disabled
there's no point in checking for https URLs.
function old new delta
P_HTTPS 6 - -6
.rodata 155501 155469 -32
parse_url 476 423 -53
------------------------------------------------------------------------------
(add/remove: 0/1 grow/shrink: 0/2 up/down: 0/-91) Total: -91 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Unfortunately, chroot() works only for root user, because of attacks
on setuid binaries (make DIR/lib/ld-linux.so a shell, hardlink to
a setuid binary, chroot to DIR, execute it and get root shell).
function old new delta
ftpd_main 2160 2180 +20
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
For CONFIG_MD5_SMALL=1:
function old new delta
md5_process_block64 925 881 -44
For CONFIG_MD5_SMALL=0:
function old new delta
md5_process_block64 1603 1586 -17
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Based on the patch by Rich Felker <dalias@libc.org>
function old new delta
builtin_umask 121 161 +40
umaskcmd 318 279 -39
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Make umount -f more compatible with util-linux 2.22.2.
Before:
* 'umount -f': calls umount syscall,
if it fails calls umount2 with 'MNT_FORCE'
* 'mount -f -l': calls umount syscall,
if it fails calls umount2 with 'MNT_LAZY'. 'MNT_FORCE' dropped
After:
* 'umount -f': calls umount2 syscall with 'MNT_FORCE'
* 'mount -f -l': calls umount2 syscall with 'MNT_LAZY' and 'MNT_FORCE'
function old new delta
umount 45 - -45
umount_main 610 555 -55
Signed-off-by: Anton Bondarenko <anton.bondarenko@axis.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Rename the defines not present in linux UAPI headers to better reflect
their purpose.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Most applets include linux' user API headers instead of duplicating
the definitions. Make it the case for i2c-tools as well.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Commit 549deab caused this sequence of commands:
mkdir foo
cd foo
touch a b
echo "./"*
to return './*' instead of the expected './a ./b'. The problem
was caused by the backport of commit 880d952 from dash. In dash
the issue was fixed by two further commits by Herbert Xu:
<d6d06ff> [EXPAND] Fixed non-leading slash treatment in expmeta
<36f0fa8> [EXPAND] Fix slash treatment in expmeta
(See git://git.kernel.org/pub/scm/utils/dash/dash.git)
Apply these fixes to BusyBox ash, thus causing the new test
glob3.tests to succeed.
function old new delta
expmeta 469 528 +59
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Similar to the "big" util-linux version. For !DMESG_PRETTY, the option is accepted
(but ignored) as well, for compatibility reasons.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
When a static interface with explicit gateway and metric in /etc/network/interfaces
is enabled using 'ifup', and further, the BusyBox 'ip' applet is enabled, the
following error message appears at the console (and no default route is added):
ip: either "to" is duplicate, or "prio" is garbage
Tracing ifup reveals that it is attempting to run the following shell command:
ip route add default via <GW> dev <DEVICE> prio <METRIC>
'ip' does not understand the 'prio' argument, causing this error. With 'metric',
it works fine.
Signed-off-by: Alex Dowad <alexinbeijing@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Static build with CONFIG_PAM fails on Debian Jessie due to undefined
references to libdl and libaudit.
Static build without pam, but with libcrypt required fails as well due
to undefined references to libpthread.
Fix these two cases by adding the missing libraries to LDLIBS when
appropriate.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Since there is no interest in merging a config option for WANT_TIMING,
remove the parts of code depending on it altogether.
While we're at it: add some newlines to improve readability.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
In the initial submission struct bbunit_listelem was manipulated by
custom list functions implemented in bbunit.c. Since the tests are now
added to the list by llist_add_to_end(), which allocates the llist_t
objects behind the scenes, there's no need for the *next field.
function old new delta
unit_main 142 141 -1
bbunit_strrstr_elem 24 16 -8
bbunit_obscure_weak_pass_elem 24 16 -8
bbunit_obscure_strong_pass_elem 24 16 -8
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 0/4 up/down: 0/-25) Total: -25 bytes
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Commit 1ecb996 attempted to make read_lines() use the last column of
the terminal (as re_wrap() did). There were two problems with this:
- The size of the buffer allocated for lines wasn't increased to allow
for the extra character.
- The test for width overflow was moved after the point where the
next character was added to the buffer. This caused a buffer overflow
in certain circumstances.
For example, if the line beyond the end of the display was wider than
the display read_lines() would initially read the partial line into a
buffer. When the user moved down read_lines() would be called again
to ensure the rest of the line was read. This would place the next
character in the partial line before checking for overflow.
This can be fixed by moving the test for overflow back to where it was
before commit 1ecb996 and changing the comparison to `>` rather than
`>=`.
There are two other places where buffers are created without allowing
for width+1 characters.
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
A mailing list thread in September 2013 discussed changing the string
returned by the non-POSIX 'uname -o' option. Nothing ever came of this
because there was no agreement as to what the string should be.
Make the string configurable so that people can decide for themselves.
Signed-off-by: Ron Yorston <rmy@frippery.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Test explicitly for REOPEN flags: update_num_lines is called
unconditionally so (num_lines != NOT_REGULAR_FILE) is also true when
num_lines contains a valid number of lines.
The call to fstat doesn't need to be in #if ENABLE_FEATURE_LESS_FLAGS:
the whole function is already in such a test.
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Fix -B with single line changes. They were always ignored regardless
if they were blank or not.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
When read_lines tests whether a character will fit on the current
line it checks the *next* character but in case of overflow doesn't
display the *current* one. This results in the last column of the
terminal never being used.
The test in re_wrap (used when the terminal width changes or line
numbers are enabled/disabled) is different: it does allow the use
of the final column.
function old new delta
read_lines 764 770 +6
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 1/0 up/down: 6/0) Total: 6 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Much of the code refers to lines using indices into the flines
array (which splits lines into portions that fit on the terminal).
In some cases this is wrong and actual line numbers should be
used:
- when lines are being truncated rather than wrapped (-S flag)
- when line numbers have been entered by the user
Also fix a bug in numeric input and improve the display at EOF.
function old new delta
goto_lineno - 111 +111
cap_cur_fline - 101 +101
buffer_to_line - 56 +56
buffer_up 35 66 +31
less_main 2606 2615 +9
goto_match 125 127 +2
buffer_down 81 56 -25
buffer_line 64 - -64
------------------------------------------------------------------------------
(add/remove: 3/1 grow/shrink: 3/1 up/down: 310/-89) Total: 221 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Add a function to package the test that detects whether enough has
been read from the file to allow a screenful to be displayed.
Also use this to determine when to display '(END)' in the status
line. The previous code was incomplete and didn't handle truncated
lines (-S flag) properly.
function old new delta
at_end - 63 +63
status_print 111 109 -2
read_lines 819 764 -55
getch_nowait 319 264 -55
------------------------------------------------------------------------------
(add/remove: 1/0 grow/shrink: 0/3 up/down: 63/-112) Total: -49 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Move the code to detect non-regular files to the point where the
file is being opened. If num_lines == READING_FILE guarantees
that the file is regular.
Detect when a file becomes unreadable between it first being opened
and the call to update_num_lines. Mark the file as being non-regular
so we don't try that again.
function old new delta
reinitialize 197 245 +48
update_num_lines 159 127 -32
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 1/1 up/down: 48/-32) Total: 16 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Currently when you disable fancy echo, escape sequences are hardcoded
enabled (e.g. as if you used `echo -e` all the time). The opposite
behavior is more desirable (always disable -e support) because:
* This seems to contradict the spirit of the kconfig help text (where
it says enable support for -n/-e flags), although you could say that
we aren't supporting the -e flag directly as `echo -e` will show the
-e flag.
* POSIX makes escape sequences optional, and even says they are there
only on XSI-conformant systems.
* It saves space (~100 bytes on x86_64).
* It makes things faster!
* It makes it behave more like bash where you need an explicit -e flag
in order for escape sequences to be interpreted.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
In commit b5c7220e7b
"fbset: respect rgba configuration lines in fb.modes"
I somehow managed to swap the offset/length markers around.
The man page for fb.modes says it should be offset/length
not length/offset as I was accidentally parsing it.
As my fb.modes file was also reversed I didn't notice
until I tried someone elses fb.modes file. Mea culpa.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
While RFC1035 recommends a label not to start with a number, there is
actually no such limitation in dns. One may buy a domain name like
0x1.net and use it.
This commit remove this check and allow a user to use such domains.
Signed-off-by: Arthur Gautier <baloo@gandi.net>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Make verbose status messages (-m/-M flags) behave more like the
real `less` command:
- fix display of line numbers so they're correct whether lines are
being truncated (-S flag) or wrapped.
- don't display total lines or percentage when lines are read from
stdin: we don't have that information until we reach EOF. When
we do reach EOF the additional information is displayed.
- when lines are read from a file count the total number of lines
so that we can display percentages. Counting lines is avoided
until the information is actually needed. If the user pages to
EOF the separate read pass can be avoided entirely.
Fixes Bug 7586
function old new delta
m_status_print 195 382 +187
safe_lineno - 35 +35
reinitialize 172 182 +10
read_lines 675 685 +10
buffer_fill_and_print 178 169 -9
------------------------------------------------------------------------------
(add/remove: 1/0 grow/shrink: 3/1 up/down: 242/-9) Total: 233 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Based on the patch by Ari Sundholm <ari@tuxera.com>
function old new delta
sync_main 20 163 +143
packed_usage 30653 30673 +20
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 2/0 up/down: 163/0) Total: 163 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Introduce a library routine to package the idiom:
p = xmalloc(b, n);
memcpy(p, b, n);
and use it where possible. The example in traceroute used xzalloc
but it didn't need to.
function old new delta
xmemdup - 32 +32
last_main 834 826 -8
make_device 2321 2311 -10
common_traceroute_main 3698 3685 -13
readtoken1 3182 3168 -14
procps_scan 1222 1206 -16
forkchild 655 638 -17
------------------------------------------------------------------------------
(add/remove: 1/0 grow/shrink: 0/6 up/down: 32/-78) Total: -46 bytes
Signed-off-by: Ron Yorston <rmy@frippery.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Lines are rewrapped when the terminal width changes or line numbers
are enabled/disabled. The current calculation always adds eight to
the line length for a tab whereas it should only add enough to move
to the next tab stop.
This doesn't affect the display of lines, which is handled elsewhere
and gets tab stops right, but it does cause lines to be wrapped at
the wrong position.
Signed-off-by: Ron Yorston <rmy@frippery.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Line numbers are displayed incorrectly on lines that have a search
pattern highlighted. The problem can be fixed by moving the call to
lineno_str in print_found above the while loop that alters the value
of the line pointer. However, a more substantial rewrite results in
savings.
function old new delta
buffer_print 688 697 +9
.rodata 156077 156045 -32
lineno_str 85 - -85
------------------------------------------------------------------------------
(add/remove: 0/1 grow/shrink: 1/1 up/down: 9/-117) Total: -108 bytes
Signed-off-by: Ron Yorston <rmy@frippery.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The -S flag, to cause long lines to be truncated, was enabled by
FEATURE_LESS_DASHCMD. This is non-obvious and -S is useful even
if the '-' command isn't enabled.
function old new delta
.rodata 156045 156077 +32
packed_usage 30223 30244 +21
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 2/0 up/down: 53/0) Total: 53 bytes
Signed-off-by: Ron Yorston <rmy@frippery.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Now that the only thing protected by setjmp/longjmp is the saved string,
we can allocate it on the stack to get rid of the jump.
Based on commit bd35d8e from git://git.kernel.org/pub/scm/utils/dash/dash.git
by Herbert Xu.
function old new delta
readtoken1 3182 3116 -66
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-66) Total: -66 bytes
Signed-off-by: Ron Yorston <rmy@frippery.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Commit 503a0b8 from git://git.kernel.org/pub/scm/utils/dash/dash.git
by Herbert Xu says:
>The parsebackquote flag is only used in a test where it always has the
>value zero. So we can remove it altogether.
The first statement is incorrect: parsebackquote is non-zero when
backquotes (as opposed to $(...)) are used for command substitution.
It is possible for the test to be executed with parsebackquote != 0 in
that case.
The test is question checks whether quotes have been closed, raising
the error "unterminated quoted string" if they haven't. There seems
to be no good reason to allow unclosed quotes within backquotes. Bash,
hush and dash (after commit 503a0b8) all treat the following as an error:
XX=`"pwd`
whereas BusyBox ash doesn't. It just ignores the unclosed quote and
executes pwd.
So, parsebackquote should be removed but not for the reason stated.
function old new delta
parsebackquote 1 - -1
readtoken1 3222 3182 -40
------------------------------------------------------------------------------
(add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-41) Total: -41 bytes
Signed-off-by: Ron Yorston <rmy@frippery.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Adding support to install individual binaries if the option is
enabled. This also installs the shared libbusybox.so.* library.
Signed-off-by: Clayton Shotwell <clshotwe@rockwellcollins.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Since there are now more statements in the if block after the while loop
in list_i2c_busses_and_exit(), there's no need for a label.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Split i2cdump_main() into shorter functions. Simplify the code a bit.
Make block an array of ints so that we can store negative results of
read functions (fixes a bug found by Denys Vlasenko).
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
We should only warn the user about addresses to be skipped if
(mode == DETECT_MODE_AUTO).
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Addresses 0x00-0x02 shouldn't be scanned by default. This patch makes
'first' default to 0x03 and only enables lower addresses if '-a' option
is passed
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
We can't use i2c_set_slave_addr() in i2cdetect, as we have to check for
EBUSY after calling ioctl(I2C_SLAVE) and print 'UU' on busy addresses
instead of bailing-out.
While we're at it: reorder definitions of local vars in i2cdetect_main().
function old new delta
i2cdetect_main 703 744 +41
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 1/0 up/down: 41/0) Total: 41 bytes
text data bss dec hex filename
826097 4164 9584 839845 cd0a5 busybox_old
826145 4164 9584 839893 cd0d5 busybox_unstripped
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Additionally, open(2) failures do not make the program die immediately.
This makes the behavior of the program match coreutils more closely.
function old new delta
truncate_main 161 221 +60
Signed-off-by: Ari Sundholm <ari@tuxera.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The commit
ash: move parse-time quote flag detection to run-time
breaks pattern substitution in parameter expansion. Fix this and
revise the code so that the different handling of the pattern and
the replacement string takes place in rmescapes rather than the
separate function parse_sub_pattern.
function old new delta
rmescapes 227 273 +46
static.qchars 3 4 +1
subevalvar 1177 1157 -20
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 2/1 up/down: 47/-20) Total: 27 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Because the parser does not recursively parse parameter expansion
with respect to quotes, we can't accurately determine quote status at
parse time. This patch works around this by moving the quote detection
to run-time where we do interpret it recursively.
Test case:
foo=\\ echo "<${foo#[\\]}>"
Old result:
<\>
New result:
<>
Do not quote back slashes in parameter expansions outside quotes.
Test case:
a=/b/c/*
b=\\
echo ${a%$b*}
Old result:
/b/c/*
New result:
/b/c/
Based on commits 880d952, 7cfd8be, 0d7d660 and a7c21a6 from
git://git.kernel.org/pub/scm/utils/dash/dash.git by Herbert Xu
function old new delta
argstr 1164 1193 +29
memtodest 147 174 +27
subevalvar 1153 1177 +24
redirect 1279 1282 +3
dolatstr 5 7 +2
static.spclchars 10 9 -1
expandarg 962 960 -2
evalcase 273 271 -2
evalcommand 1204 1197 -7
rmescapes 236 227 -9
preglob 27 8 -19
evalvar 604 582 -22
cmdputs 389 334 -55
readtoken1 3163 3061 -102
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 5/9 up/down: 85/-219) Total: -134 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Collapsing arithmetic expansion is incorrect when the inner arithmetic
expansion is a part of a parameter expansion.
Test case:
unset a
echo $((3 + ${a:=$((4 + 5))}))
echo $a
Old result:
12
(4 + 5)
New result:
12
9
Based on commit bb777a6 from git://git.kernel.org/pub/scm/utils/dash/dash.git
by Herbert Xu
function old new delta
readtoken1 3180 3163 -17
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Based on commits 1a74845, cfc3d6a and ff13779 from
git://git.kernel.org/pub/scm/utils/dash/dash.git by Herbert Xu
function old new delta
evalcommand 1197 1204 +7
localcmd 327 325 -2
readtoken1 3200 3180 -20
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 1/2 up/down: 7/-22) Total: -15 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Test case:
unset a
echo "${a:-~root}"
Old result:
/root
New result:
~root
Based on commit 170f44d from git://git.kernel.org/pub/scm/utils/dash/dash.git
by Herbert Xu
function old new delta
evalvar 598 604 +6
parse_command 1440 1443 +3
localcmd 325 327 +2
readtoken1 3199 3200 +1
argstr 1180 1164 -16
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 4/1 up/down: 12/-16) Total: -4 bytes
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Previously tilde expansion was not carried out for =?#% expansion words.
Test case:
a=~root:~root
echo ${a#~root}
Old result:
/root:/root
New result:
:/root
Based on commit dd721f71 from git://git.kernel.org/pub/scm/utils/dash/dash.git
by Herbert Xu
function old new delta
subevalvar 1152 1153 +1
Signed-off-by: Ron Yorston <rmy@pobox.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
fixes segfault introduced in 0a0acb55db with functions using "local -".
test-case: f() { local -; local x; }; f
note: with this change applied multiple 'local -'s still cause multiple entries to be added to the localvars list.
this problem will be addressed in a separate commit.
Signed-off-by: Eugene Rudoy <gene.devel@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Linux recently gained a new config option, CONFIG_MULTIUSER, that makes
support for non-root users optional. This results in a number of syscalls
being disabled: setuid, setregid, setgid, setreuid, setresuid, getresuid,
setresgid, getresgid, setgroups, getgroups, setfsuid, setfsgid, capget,
capset.
Currently a number of busybox applets, including login, struggle to run
when CONFIG_MULTIUSER is disabled. Even the root user is unable to login:
login: can't set groups: Functi
This patch adds code to make change_identity() a nop on single user
systems. It works by recognising the signature errno value (ENOSYS, due
to the system calls being disabled) and, to avoid security risks, only
deploys when the current uid and target uid is the same.
After the patch is applied any attempt to switch to a non-root user will
fail. Thus a badly configured userspace (for example, one that tries to
start a daemon as a non-root user when the kernel cannot support this)
will report errors as one would expect.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Trying to access /dev/i2c/* on every error after opening /dev/i2c-* can
mislead users who e.g. don't have root access. Instead of bailing-out
with "permission denied" we currently print "no such file or directory".
Fix it by trying open("/dev/i2c/%d") only if we got ENOENT.
Upstream i2cdetect tries to get any info it can from /sys and /proc even
when invoked by an unprivileged user, but we don't want to add unnecessary
bloat.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Currently basic undo functionality with the 'u' key depends on
FEATURE_VI_YANKMARK. These two features are separate, so we can remove this
dependency.
Signed-off-by: Andrew Fuller <abf@google.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This also removes their help texts.
function old new delta
run_applet_no_and_exit 442 452 +10
packed_usage 30713 30625 -88
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This was seen to happen if two mdevs are run in parallel,
mdev.seq is empty, and the "newer" one manages to write it first.
function old new delta
mdev_main 1366 1388 +22
atoll - 20 +20
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Regression added in commit 14158b4127
"find: add optional support for '-exec ... {} +'"
This commit causes find to exit on the first path argument that was not
found, which breaks existing scripts and is incompatible to other
implementations.
Instead of exiting on the first failure, return EXIT_FAILURE at the end
if any error occurred.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Copyright years seem to be out of date, e.g. coreutils/truncate.c
has Copyright (C) 2015.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Bernhard Reutner-Fischer <rep.dot.nop@gmail.com>
UTMP is SVID legacy, UTMPX is mandated by POSIX.
Glibc and uClibc have identical layout of UTMP and UTMPX, both of these
libc treat _PATH_UTMPX as _PATH_UTMP so from a user-perspective nothing
changes except the names of the API entrypoints.
Signed-off-by: Bernhard Reutner-Fischer <rep.dot.nop@gmail.com>
Commit "zcip: fix link-local IP conflict detection" has introduced
wrong comparsion of source IP with our IP. This leads to a new IP
being picked unnecessarily on every incoming ARP packet.
Signed-off-by: Vladislav Grishenko <themiron@mail.ru>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This way it can be used by other applets without duplication.
Signed-off-by: Ari Sundholm <ari@tuxera.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This is basically a combination of the default (dump mode) and -f
(follow mode). Specifying -F makes logread first dump the log buffer and
then immediately start following it.
function old new delta
packed_usage 30412 30443 +31
logread_main 491 497 +6
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
When 'if -a' runs into an failure on an interface all further
interfaces won't be correctly updated in ifstate. This patch
inserts a new variable that only tracks the current interfaces
failure so that the write to ifstate can rely on this and not
the one for the functions return value.
Fixes https://bugs.busybox.net/show_bug.cgi?id=6212
Signed-off-by: Frank Bergmann <frank.frajasalo@googlemail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The CPPFLAGS/CFLAGS settings might have features that matter, so make
sure we utilize them when testing the compiler.
URL: https://bugs.gentoo.org/471118
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
arping: interface eth0 not found: No such device
^^^^
This is because error template is formed before parsing command line arguments,
so it always uses default interface name "eth0".
Signed-off-by: Alexander Korolkov <alexander.korolkov@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
function old new delta
mount_main 1221 1241 +20
packed_usage 30616 30610 -6
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Isaac Dunham <ibid.ag@gmail.com>
There is no reason to do so. We do not even have SIGCHLD handler.
function old new delta
runsvdir_main 1077 1057 -20
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
We could lose a signal while processing previous one
function old new delta
runsvdir_main 1088 1077 -11
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Without this patch acpid can't log the events at all. Moreover it tries
to truncate log file every time.
Signed-off-by: Serj Kalichev <serj.kalichev@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
https://bugs.debian.org/538685
dc requires whitespace between language elements.
We were requiring
1 2 + p
instead of the abbreviated
1 2+p
(for example).
function old new delta
stack_machine 97 126 +29
dc_main 117 79 -38
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 1/1 up/down: 29/-38) Total: -9 bytes
Signed-off-by: Bernhard Reutner-Fischer <rep.dot.nop@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
usecase:
two sd cards are being mounted in parallel at same time on dual core. example
modules which are getting loaded is nls_cp437. While one module is being
loaded , it makes state in /proc/modules as 'coming' and then starts doing its
module init function (in our case - registering nls). meanwhile on other core,
if modprobe returns that is has already been loaded, then it will continue
and search for the nls list which is not yet finished from first module init.
This fails resulting in not mounting sd card.
function old new delta
process_module 667 746 +79
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
"rmmod OUT_OF_TREE_MODULE" was not working, because module is not in depmod file.
In general, rmmod doesn't need scanning, it simply unloads every argv[i].
function old new delta
rmmod - 63 +63
modprobe_main 449 465 +16
process_module 705 667 -38
------------------------------------------------------------------------------
(add/remove: 1/0 grow/shrink: 1/1 up/down: 79/-38) Total: 41 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
loopinfo.lo_file_name is not enough to uniquely identify a file on a system with
multiple mount namespaces. We could conceivably change this to dedup on
(lo_rdevice, lo_inode), but, as the comment above the deleted code notes, this
whole approach of reusing devices is racy anyway, so it seems better to stop
doing it entirely.
Signed-off-by: Kevin Wallace <k@igneous.io>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Storing the original file's modification time in the output file is
harmful (precludes deterministic results) and unlike official gzip,
the busybox version provides no way to suppress this behavior; the -n
option is silently ignored. Rather than trying to make -n work, this
patch just removes the timestamp-storing functionality. It should be
considered deprecated anyway; it's not Y2038-safe and gunzip ignores
it by default.
Per RFC 1952, 0 is the correct value to store to indicate that there
is no timestamp.
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Some images do not have the default VID offset. The option -O must
be used to attach such images.
Signed-off-by: Micke Prag <micke.prag@telldus.se>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
(re-sending this as it got ignored completey and the format of the
previous mail was probably not correct - please let me know if there's
anything else I can do to get this trivial fix applied)
for telnetd to work, we only need CONFIG_UNIX98_PTYS to be enabled
in the Linux kernel - DEVPTS_FS has been obsolete for some time
Signed-off-by: Martin Kaiser <lists@kaiser.cx>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This speeds up syncing - now happens only just
two replies from a peer. Especially useful for "ntpd -q".
Shouldn't have ill effects: if we chose a bad peer,
we will discover it later and switch to another one.
The code is even smaller this way.
Suggested by Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
We wanted to detect when tv_sec = unsigned1 - unsigned2
underflows by looking at tv_sec's sign. But if tv_sec
is long and it is wider than unsigned, we get unsigned -> long
conversion which is in this case never negative.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This fixes a regression introduced with commit 78854520 (modprobe:
revert checking for /, stop doing basename() on modprobe args,
2015-01-01) that broke modprobe options stored in /etc/modprobe.conf and
/etc/modprobe.d/*.conf.
This also fixes modprobe -r
Signed-off-by: Natanael Copa <ncopa@alpinelinux.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
"modprobe -r MODNAME", after it found the full module pathname,
should strip dirpath before trying to remove the module.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
If the :r command is used to read a file after the last line of the
buffer the last line of the buffer and the first line of the file
are joined. An extra blank line appears at the end of the buffer.
file 1
file 1
file 1file 2
file 2
file 2
~
~
The insertion point is normally at the start of the line following the
specified line. When the specified line is the last one the next_line
function baulks at moving to the non-existent following line.
Signed-off-by: Ron Yorston <rmy@tigress.co.uk>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Commit 32afd3a introduced these regressions on the master branch:
Starting vi with no filename on the command line gives the status message
"'(null)' Bad address" instead of "- No file 1/1 100%".
Starting vi with a non-existent file on the command line gives the status
message "'new.txt' No such file or directory" instead of "- new.txt 1/1 100%"
Signed-off-by: Ron Yorston <rmy@tigress.co.uk>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
OpenNTPd is licensed under ISC-style license so it's good idea to keep
ntpd applet under same license to avoid mess, instead of having
our changes to be under GPL.
Names of original code's authors are added.
Signed-off-by: Adam Tkac <vonsch@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This saves a bit of memory but more importantly, allows to create
xmalloc_getpwnam() API where result can be deleted simply using free().
function old new delta
getXXnam 134 173 +39
parse_common 188 212 +24
convert_to_struct 277 290 +13
get_S 90 88 -2
tokenize 129 126 -3
bb_internal_getpwent_r 175 172 -3
getXXnam_r 208 198 -10
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 3/4 up/down: 76/-18) Total: 58 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Previous code's trick with bitwise OR was giving this on 32-bit x86:
sizeof(struct passwd):28
sizeof(struct group):16
sizeof(struct spwd):36
sizeof(struct_result):60
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This target doesn't work with current directory layout. Just make cscope
index all .c and .h files.
While we're at it: add cscope output files to .gitignore.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Prevent nasty surprises if script runs longer than lease time / 2.
Signed-off-by: John Schroeder <jschroed@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Based on the following user report:
I ran into an issue where I was seeing a long delay in the scripts called
in udhcp_run_script. I was using an old version of OpenWrt (kamikaze)
and a satellite modem. An NTP script was being called and the modem
would sometimes take a long time to respond to the DNS lookup when
it was offline.
This delay started affecting my lease time. The lease that I would
get from my satellite modem before it was online would be short:
only 60 seconds. The delay with NTP and the modem would typically
be about 18 seconds. This would cause the first DHCP renew request
from dhcpc to be a little late. Under certain circumstances,
I could even see the first DHCP renew to occur after the lease
had expired!
function old new delta
udhcpc_main 2816 2837 +21
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The --bb options now depends on LONG_OPTS. Omit mentions of --bb from usage
text when LONG_OPTS is disabled.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The Required_argument macro is only defined when long options are enabled.
Fixes the following build error:
miscutils/nandwrite.c: In function 'nandwrite_main':
miscutils/nandwrite.c:120:10: error: expected ',' or ';' before 'Required_argument'
Reported-by: Christian Kästner <kaestner at cs.cmu.edu>
Signed-off-by: Baruch Siach <baruch at tkos.co.il>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
In vi-mode lineedit tries to detect some escape sequences.
After the ESC it reads the next character to check for certain
values. This read should have a timeout or a user-entered ESC to
switch to command mode doesn't properly handle the next character.
Signed-off-by: Ron Yorston <rmy@tigress.co.uk>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Man entry for sendfile:
Not specified in POSIX.1-2001, or other standards.
Other UNIX systems implement sendfile() with different semantics and
prototypes. It should not be used in portable programs.
Select PLATFORM_LINUX if enabling FEATURE_USE_SENDFILE.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
some flash partitions can be smaller than the existing BUFSIZE thus write
BUFSIZE will fail with "no space left on device"
Signed-off-by: Jacob Kjaergaard <jacob.kjaergaard@prevas.dk>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Busybox already uses sendfile in httpd. This patch proposes to use it
globally to copy data between file descriptors.
It speeds up the copying on slow systems a lot - below are the times needed
to copy a 450Mb file with and without this option enabled on a BeagleBone
Black:
sendfile:
user 0m0.000s
sys 0m8.170s
read/write 4k:
user 0m0.470s
sys 0m16.300s
function old new delta
bb_full_fd_action 394 474 +80
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Sometimes ARG_MAX is small (like 32k) yet sysconf(_SC_ARG_MAX)
is big, and people prefer using the bigger value.
OTOH, with sufficiently large ARG_MAX, further wins from
sysconf(_SC_ARG_MAX) being bigger are exponentially smaller:
you can see 4 times fewer fork+execs when you run find, but
when each execed process already takes a thousand parameters
it's likely execution time is dominated by what that process
does with each parameter.
Thus, with this change ARG_MAX is used if it's sufficiently big,
otherwise sysconf(_SC_ARG_MAX) is used.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
169.254 may already be used by a local network. This patch allows
specifying your own IP range.
Our particular use case is a mesh network, in which the nodes partaking
were using an IP range specifically assigned for the meshing purpose.
As the LAN side of the mesh node could use 169.254, this default range
was not an option.
function old new delta
zcip_main 1342 1426 +84
pick_nip - 40 +40
packed_usage 29974 29969 -5
pick 34 - -34
------------------------------------------------------------------------------
(add/remove: 1/1 grow/shrink: 1/1 up/down: 124/-39) Total: 85 bytes
Signed-off-by: Michel Stam <m.stam@fugro.nl>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Some clients have a very short timeout for sending the DHCP
DISCOVER, shorter than the arpping timeout of 2000 milliseconds
that udhcpd uses by default.
This patch allows tweaking the timeout, or disabling of arpping
altogether, at the risk of handing out addresses which are
already in use.
function old new delta
udhcpd_main 1460 1501 +41
udhcpc_main 2814 2851 +37
packed_usage 29957 29974 +17
arpping 477 493 +16
find_free_or_expired_nip 161 174 +13
send_offer 285 292 +7
nobody_responds_to_arp 85 89 +4
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 7/0 up/down: 135/0) Total: 135 bytes
Signed-off-by: Michel Stam <m.stam@fugro.nl>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The offset to jitter ratio is now calculated before updating
jitter to make the test more sensitive.
function old new delta
ntp_init 460 474 +14
update_local_clock 752 764 +12
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 2/0 up/down: 26/0) Total: 26 bytes
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
To avoid polling servers frequently slowly increase the interval up
to BIGPOLL when
- no replies are received from a peer
- no source can be selected
- peer claims to be unsynchronized (e.g. we are polling it too
frequently)
When recv() returns with an error, drop code to try to continue
on network errors: I'm not convinced those cases happen in real life.
function old new delta
recv_and_process_peer_pkt 919 838 -81
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
* on step, poll interval drops to 8.5 mins instead of 32 seconds
* on total loss of all replies (no replies from any peer
for last 8 requests), also drop poll interval to 8.5 mins
instead of 32 seconds
* on send abd recv errors, RETRY_INTERVAL is now 32 seconds,
not 5 seconds
* on timing out listening to reply, instead of unconditional
shortening poll interval by x4, clamp it to NOREPLY_INTERVAL
(512 seconds)
* if a largish offset is seen, clamp nexp poll interval
to 128 seconds, not 64 seconds
function old new delta
clamp_pollexp_and_set_MAXSTRAT - 37 +37
recv_and_process_peer_pkt 861 869 +8
poll_interval 52 48 -4
update_local_clock 762 752 -10
ntpd_main 1063 1050 -13
------------------------------------------------------------------------------
(add/remove: 1/0 grow/shrink: 1/3 up/down: 45/-27) Total: 18 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The burst mode needs to be stopped even when no replies are received.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Some packages want to install themselves using "-t" to specify
the directory (as supported by GNU coreutils). Add support for the option
for compatibility reasons.
function old new delta
install_longopts 76 95 +19
install_main 769 777 +8
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 2/0 up/down: 27/0) Total: 27 bytes
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This makes "G" (goto end of input) command work as well as
/search_for_nonexistent_string: both will read to EOF now
even from somewhat slow input (such as kernel's "git log").
function old new delta
ndelay_on 35 43 +8
ndelay_off 35 43 +8
read_lines 695 691 -4
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 2/1 up/down: 16/-4) Total: 12 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
While at it, fix brace matching to actually show the match
(missed fflush was causing cursor positioning to be buffered);
shorten brace matching code; remove unused macro indirection
in indicate_error().
Custom linker script 'busybox_ldscript' found, using it
function old new delta
indicate_error - 61 +61
mysleep 43 56 +13
char_insert 483 486 +3
find_pair 167 124 -43
Indicate_Error 61 - -61
------------------------------------------------------------------------------
(add/remove: 1/1 grow/shrink: 2/1 up/down: 77/-104) Total: -27 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
It used to be aliased to !FEATURE_SH_EXTRA_QUIET for ash,
while hush had it separate from FEATURE_SH_EXTRA_QUIET.
Bring ash in line with hush.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Some HP PA-RISC firmware always sends fixed 512-byte requests,
with trailing garbage.
function old new delta
tftpd_main 578 572 -6
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
It is not clear why we were excluding init from this.
The "getpid() != 1" clause was there from the beginning (2001)
but not explained.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
display_header() code to parse meminfo as is was buggy:
- uninitialized variables were used if meminfo was not as expected
- meminfo parsing failed on new kernels (3.14+) as new field 'MemAvailable'
was introduced between MemFree and Buffers
- shared memory was handled only for ancient kernels (2.4.x and earlier)
as result Buffers and shared memory fields were shown with bogus values
on current kernels.
The new code does not try to parse the old style summary header, as the
separated fields are always present (it saves code size). Additionally,
both Shmem (2.6+) and MemShared (2.4 and earlier) fields are now parsed
and summed for shared memory usage; as only one of them exists depending
on kernel version.
display_topmem_header() parses also meminfo so this makes it use the
same code for code shrink.
function old new delta
display_header - 681 +681
display_topmem_process_list 465 684 +219
parse_meminfo - 189 +189
static.fields - 106 +106
static.match 132 - -132
.rodata 120254 120117 -137
display_topmem_header 513 - -513
display_process_list 1705 667 -1038
------------------------------------------------------------------------------
(add/remove: 3/2 grow/shrink: 1/2 up/down: 1195/-1820) Total: -625 bytes
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
It is an interesting trick, but so far I only managed to make it work
correctly, not to make it faster and/or smaller.
The code is ifdefed out for now.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
During link-local IP resolution, if a regular ARP request is received
during the ARP probe period, it will incorrectly cause a target IP
conflict. This then leads to a new IP being picked unnecessarily.
Per RFC 3927, section 2.2.1, we should flag a target IP conflict only if
the source IP is null, the target IP matches our IP, and the source
hw addr does not match our hw addr.
function old new delta
zcip_main 1354 1322 -32
Signed-off-by: Ken Sharp <ken.sharp@ni.com>
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Like d3092c99, this change adds support for the DHCP "path-prefix"
option, as defined in RFC 5071. We use the string identifer
"pxepathprefix".
Adding this option makes string parsing in the hook scripts simpler.
function old new delta
dhcp_option_strings 255 269 +14
dhcp_optflags 72 74 +2
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
display() function returns the length of the value we are displaying + 1.
As a consequence, if we have field=value\0field=value\0field=value in the
binary, then the second occurence will be skipped as ptr will miss the first
character of the following field.
Example trying to list aliases from ixgbe.ko on a 3.2 kernel.
- In the module we have:
alias=pci:v00008086d00001560sv*sd*bc*sc*i*\0
alias=pci:v00008086d0000154Asv*sd*bc*sc*i*\0
alias=pci:v00008086d00001557sv*sd*bc*sc*i*\0
alias=pci:v00008086d0000154Fsv*sd*bc*sc*i*\0
alias=pci:v00008086d0000154Dsv*sd*bc*sc*i*\0
...
- Using modinfo -F alias ixgbe returns:
alias: pci:v00008086d00001560sv*sd*bc*sc*i*
alias: pci:v00008086d00001557sv*sd*bc*sc*i*
alias: pci:v00008086d0000154Dsv*sd*bc*sc*i*
...
This problem appeared with kernel commit "modules: no need to align .modinfo
strings" b6472776816af1ed52848c93d26e3edb3b17adab in 2.6.37.
Fix this by not trusting display() return value but increment ptr by strlen(ptr)
(the same way as depmod.c does).
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Move last_log_time from a single global to *each logFile_t*
so that we can actually apply the logic to every log-file
in multi-file configurations, rather than working only
for the first file written in each 1-second interval
and then leaving the others connected to possibly wrong files.
Signed-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Even if we fail to write to a log-file, and it's not growing,
it's not *shrinking* either....
Signed-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
We don't have an INIT_FIRST, so let's rename INIT_LAST to INIT_FUNC
to imply that the function is called at program start-up.
Also: the priority argument for __attribute__((constructor)) isn't
used, so let's remove it.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
busybox stat tries to always print the selinux context, even if it
is not requested which leads to a segmentation fault due to
dereferencing a null-pointer.
This also changes the format-string used to print the context to
so it actually produces useful output.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
When we merely chdir to saved "real" root fd,
exec("proc/self/exe") works for static executables but not
for dynamic ones (they can't find their interpreter).
With this patch, we also *chroot* to real root.
As a bonus, this gives us proper usernames, timezone conversion
etc.
function old new delta
popen_ls 203 259 +56
ftpd_main 2362 2366 +4
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
since mtd-utils 1.4.7, the default behaviour of nanddump is skipbad
(commit 2521d4f1b6b9866a9c89f3c11a4f6a3d763ff1d7)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
since mtd-utils 1.4.7, the omit bad block method has been removed.
(cf commit d8b8f780ec3c916f3990e9227d6bfbb22bf42ef8)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
In mtd-utils, the bad block options changed in favor of
--bb=[skipbad|padbad|dumpbad] and omitbad has been removed.
This patch add the --bb=skipbad and padbad methods to busybox' nanddump.
padbad is the current default behaviour.
The difference between skipbad and omitbad is this one:
On a 16K block NAND, if the 1st block of mtd0 is bad, we'll have:
nanddump -b -l 16384 /dev/mtd0 | wc -c
0
nanddump --bb=skipbad -l 16384 /dev/mtd0 | wc -c
16384 <- data from 1st good block
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
function old new delta
unlink_main - 45 +45
packed_usage 29667 29686 +19
Signed-off-by: Isaac Dunham <ibid.ag@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This set of patches adds a simple unit-testing framework to Busybox
unit-tests: add some helper macros for unit-test framework implementation
unit-tests: implement the unit-testing framework
unit-tests: add basic documentation on writing the unit test cases
unit-tests: modify the Makefile 'test' target to run unit-tests too
unit-tests: add two example test cases
unit-tests: modify the existing strrstr test code to use the unit-test framework
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The find utility uses a hardcoded value of 32 * 1024 as the limit of
the command-line length when calling 'find -exec ... {} +'. This results
in over 4 times more execve() calls than in coreutils' find.
This patch uses the limit defined in system headers.
Based on the patch by Bartosz Golaszewski <bartekgola@gmail.com>.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Always unlink + reopen, rather than sometimes using ftruncate();
using a single code-path reduces the opportunity for either
mistakes or duplicate code.
Signed-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Forgetting to re-set log_file->size after truncating to zero
discards log-data for the next 1 second following an oversize-induced purge,
when we shouldn't necessarily throw that data away.
Signed-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Closes 627 and 7034.
Commonly seen case is (un)loading of an alias
which matches ata_generic and a more specific ata module.
For example:
modprobe [-r] pci:v00008086d00007010sv00000000sd00000000bc01sc01i80
(ata_generic and pata_acpi)
modprobe [-r] pci:v00001106d00000571sv00001509sd00009022bc01sc01i8a
(ata_generic and pata_via)
function old new delta
process_module 615 728 +113
parse_module 309 395 +86
find_alias 621 653 +32
pathname_matches_modname 78 79 +1
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 4/0 up/down: 232/0) Total: 232 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Before this cahnge, sometimes they were used after the next packet
from another peer was received, because we did updare some peer stats
from high delay packet before dropping it.
function old new delta
recv_and_process_peer_pkt 922 966 +44
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
POSIX.1-2008 removed the usleep function, provide a fallback
implementaion using the recommended nanosleep().
Signed-off-by: Bernhard Reutner-Fischer <rep.dot.nop@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
For certain cross build scenarios the LD variable is overridden
to use the gcc executive to ensure all the target tuning parameters
are used. In these cases, the executive errors out as shown below
but since this step is only linking to a .o file the standard libs
are not needed.
$ make LD=gcc applets/built-in.o
LD applets/built-in.o
/usr/bin/ld: cannot find -lgcc_s
/usr/bin/ld: cannot find -lgcc_s
collect2: ld returned 1 exit status
make[1]: *** [applets/built-in.o] Error 1
make: *** [applets_dir] Error 2
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
1) real swapon/swapoff handles also devices on the commandline with -a;
2) xstat(device) in swap_enable_disable aborts on error when cycling through
fstab so some devices are not handled;
3) duplicated code for ENABLE_FEATURE_SWAPON_DISCARD and
ENABLE_FEATURE_SWAPON_PRI was moved to functions.
4) silence some error messages with -a;
5) minor cleanups and code refactoring reduced the size as per bloat-check:
6) I also added support for /proc/swaps handling to swapoff:
"When the -a flag is given, swapping is disabled on all known swap devices
and files (as found in /proc/swaps or /etc/fstab)."
So now swapoff first cycles through /proc/swaps and then through fstab
to swapoff all devices.
function old new delta
set_discard_flag - 106 +106
swap_enable_disable 147 238 +91
set_priority_flag - 79 +79
retrieve_file_data 470 467 -3
swap_on_off_main 638 418 -220
------------------------------------------------------------------------------
(add/remove: 2/0 grow/shrink: 1/2 up/down: 276/-223) Total: 53 bytes
Signed-off-by: Tito Ragusa <farmatito@tiscali.it>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Swap entries in /etc/fstab inherit the priority specified on the command line unless they have 'pri' in their mount options.
Signed-off-by: Matt Whitlock <busybox@mattwhitlock.name>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Also, the maximum allowable value of swap priority is technically SWAP_FLAG_PRIO_MASK >> SWAP_FLAG_PRIO_SHIFT.
Signed-off-by: Matt Whitlock <busybox@mattwhitlock.name>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This patch adds some information about the gen_build_files.sh script and how
it allows to keep the Kbuild, Config.in etc. declarations in .c files.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
rand() is the most standard C library function,
and on uclibc they are the same. I guess
they are the same in most todays' libc...
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Default to ascii instead of latin1. Otherwise man pages can be displayed
incorrectly. E.g. bullets show as "<B7>".
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Currently CONFIG_PAM depends on CONFIG_LOGIN, but is used by the httpd applet too.
This patch moves said option to general configuration, thus allowing to
compile httpd with PAM support independently from login.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Does not configure anything. L2 configuration hook scripts should do
their job on receiving ADDRFAM=link. Configuration will be done only
once, irrespective of L3 protocols used.
Using the 'link' family in the interfaces file conforms to the Debian
implementation:
http://sources.debian.net/src/ifupdown/0.7.47.1/link.defn
function old new delta
link_methods - 12 +12
addr_link - 12 +12
link_up_down - 6 +6
static.addr_fams 12 16 +4
------------------------------------------------------------------------------
(add/remove: 3/0 grow/shrink: 1/0 up/down: 34/0) Total: 34 bytes
Signed-off-by: Kaarle Ritvanen <kaarle.ritvanen@datakunkku.fi>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The warning was:
warning: typedef 'BUG_const_mismatch' locally defined but not used [-Wunused-local-typedefs]
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
When you build with FEATURE_INSTALLER disabled, you get a build
warning like so:
libbb/appletlib.c: In function 'busybox_main':
libbb/appletlib.c:691:7: warning: variable 'use_symbolic_links' set but
not used [-Wunused-but-set-variable]
int use_symbolic_links;
^
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The -i/-o options were missing, and the -r/-s/-v options were
incorrectly labeled as "OS" instead of "kernel".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Apparently, some *BSD variants (and maybe some other OSes) does not define
SIGPWR signal. So since commit 760fc6debc, busybox fails to build on
such platforms. Fix this.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
In commit afa63b2dcd I replaced `type -p' with
`command -pv'. But actually it is wrong, the right
substitution is `command -v'. We need to find our
busybox which is in the first directory in $PATH, so
`command -p' should not be used because it uses
default PATH, not current value of PATH where our
busybox binary resides.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
GCC complained about since_last_update being set but not used.
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Sort now performs global reverse on fallback sort if -r is set. Before
only key local flags were checked.
function old new delta
compare_keys 712 738 +26
Signed-off-by: Bartosz Golaszewski <bartekgola@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Changes adduser.c, addgroup.c and Config.src to set and use CONFIG_LAST_ID.
function old new delta
adduser_main 841 865 +24
addgroup_main 407 425 +18
Signed-off-by: Tito Ragusa <farmatito@tiscali.it>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
We only need to check for signature-less extensions,
currently only .lzma. The rest can be happily autodetected.
This fixes "zcat FILE_WITHOUT_GZ_EXT" case, among others.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This includes proper line breaks for labels and closing braces,
and removing non-portable \n and \t in s/// functions.
Signed-off-by: Matthias Andree <matthias.andree@gmx.de>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Unfortunately, with !EXTRA_COMPAT, "grep -w ^str" still erroneously matches "strstr".
function old new delta
grep_file 1499 1510 +11
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
@@ -911,6 +908,5 @@ int test_main(int argc, char **argv)
}
ret:
DEINIT_S();
// return negate ? !res : res;
returnres;
}
Loaded 100 of 761 files, more files were not shown because too many files have changed in this diff.
Show more
Reference in new issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.